Big Stock Flash Deal 800w 24000rpm ER11 65mm 110V water cooling spinel motor&1.5kw 1phase 110V VFD inverter CNC kits


Best Water High Rating provide Machine Tool Spindle, Cheap Machine Tool Spindle, 800w 24000rpm ER11 65mm 110V water cooling spinel motor1.5kw 1phase 110V VFD inverter CNC kits Super Deals 800w 24000rpm ER11 65mm 110V water cooling spinel motor&1.5kw 1phase 110V VFD inverter CNC kits. Get 43% discount Now! Now US $213.00/piece. Dont waste your time. Buy Now only in TOPCNC Store Trusted Seller Store!

800w 24000rpm ER11 65mm 110V water cooling spindle motor&1.5kw 1phase 110V VFD inverter CNC kits

package included:

1pcs 800w 24000rpm ER11 65mm 110V water cooling spindle motor

1pc 1.5kw 1phase 110V VFD inverter

Description:

The spindle motor:

1HP 0.8kw 24000RPM ER11 water cooling Woodworking AC Spindle motor 65mm 2 bearings 110VAC 10A 400hz CNC Router

1, Spindle Specification

Brand

HY

Spindle Model

65 800w 110v

Dimension

65mm*158mm

Speed

24000rpm

Rated Power

0.8kW

Voltage

AC110V

Current

10A

Frequency

400HZ

Bearings

1*7002, 1*7000

Collet

ER11(Random send a collet as free)

Cooling Type

Water cooling

Lubricate

Grease

Plug connection:

Plug in 1234 pin, 1-U, 2-V, 3-W, 4-GND or not connected. if 123 not connected correctly, the motor will reverse. Swap any two wires can be OK.

The VFD inverter:

2HP 1.5KW 400HZ VFD Inverter Frequency converter single phase 110V input 3phase 110V output 12A for Engraving spindle motor

Instructions

1

The electric spindle must be matched with the frequency converter. Frequency converter selection must be matched with the power, voltage, current, frequency and other parameters of the electric spindle. The use of electric spindle must first set the benchmark frequency of the inverter. The reference frequency of the frequency converter is set according to the highest frequency of the electric spindle. Inverter reference frequency conversion factory default settings 50hz. If the base frequency of the inverter is not set before the spindle motor is used, the spindle motor can be burnt down.

2

Before use, you should use the hand to turn the spindle motor, and confirm that it can rotate smoothly.

3

When in use, you must first connect to the spindle motor cooling water pipes, water pipes to ensure. Water flow is not less than 5L/min

4

If the electric spindle needs to be replaced with a new bearing,
Should be replaced by a certain professional and technical personnel. Supporting special tools. The spindle motor should be fully cleaned, the stator coil does not need to be removed.

4, The common faults and their elimination methods

The Fault

The Reason

The Solution

The electric spindle does not run after start

1.No output or wrong setting for the inverter

check the output and setting of the inverter

2.Plug not connected

check the plug and connection cable

3.the cable not connected

4.The stator winding burned

change the stator

Few seconds after start,the spindle stop running

1.water inlet

Drying stator

2.High temperature induced wire insulation damage

change the stator

3.Lack of phase operation caused over current protection

check the cable connecting of the spindle motor

4.Start-up time is too short

Extended acceleration time

Motor smoke or shell hair hot

1.The inverter output voltage, frequency is not match with the spindle motor

check the setting of the inverter

2.the frequency of the inverter is not set correctly

reset the frequency of the inverter

3.Air duct blockage

check the air duct

Nut loosening when start

Rotation direction error

recorrect the rotation according the instruction on spindle

Noise and vibration

1,bearing damaged

change bearings

2.Parts precision damage affect dynamic balance

Check dynamic balance

3.Large spindle runout

change spindle

Nut loosening when stop

Down time is too short

Prolonged deceleration time

Return Policy

If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.

Seller Service

On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).
2018 Cheap 800w 24000rpm ER11 65mm 110V water cooling spinel motor&1.5kw 1phase 110V VFD inverter CNC kits

Comments

Popular posts from this blog

Wonderful Promotion Kitchen faucet mixer chrome finished water filter ro faucet 3 way water tap black three colors

Terrific Discount 2017 luxury brand Mechanical men rose gold watches automatic watch water resistant full Stainless Steel elegant watch for men

Super Clearance Mens luxury black wristwatches male brand watches quartz man clock waterproof stainless steel fashion Business luminous calendar