Fantastic Sale 300w 0.3kw ER8 60000rpm Precision High Speed spindle motor water cooling 75VAC 4.5A 1000HZ GDZ48-300 CNC Router
Best Water High Rating provide router aluminum, router atc, router bits for granite Great Promo 300w 0.3kw ER8 60000rpm Precision High Speed spindle motor water cooling 75VAC 4.5A 1000HZ GDZ48-300 CNC Router. Get 43% discount Now! Now US $211.00/piece. Dont waste your time. Buy Now only in TOPCNC Store Trusted Seller Store!
300w 0.3kw ER8 60000rpm Precision High Speed spindle motor water cooling 75VAC 4.5A 1000HZ GDZ48-300 CNC Router
1, Spindle Specification
spindle motor model | GDZ48-300 |
Brand | Chang Sheng |
Certification | ISO9001-2000 |
Product type | High-Speed Constant Torque Motorized Spindle Motor |
Applications | for CNC Engraving Machine |
Pole number | 2 |
Rated power(KW) | 0.3Kw |
Rated voltage(V) | 75V |
Rated speed(rpm) | 60000 r/min |
Current(A) | 4.5A |
Frequency(Hz) | 1000Hz |
Cooling | Water cooling |
Bearing type | 1×C136101 1×C136018 |
Lubricate | grease |
Collet(mm) | ER8, 3.175mm(default) |
Repair time | bearing(half year),spindle(one year) |
Diameter D (mm) | 48mm |
Complete Length L(mm) | 120mm |
Plug connection: | Plug in 1234 pin, 1-U, 2-V, 3-W, 4-GND or not connected. if 123 not connected correctly, the motor will reverse. Swap any two wires can be OK. |
2, Instructions
1 | The electric spindle must be matched with the frequency converter. Frequency converter selection must be matched with the power, voltage, current, frequency and other parameters of the electric spindle. The use of electric spindle must first set the benchmark frequency of the inverter. The reference frequency of the frequency converter is set according to the highest frequency of the electric spindle. Inverter reference frequency conversion factory default settings 50hz. If the base frequency of the inverter is not set before the spindle motor is used, the spindle motor can be burnt down. |
2 | Before use, you should use the hand to turn the spindle motor, and confirm that it can rotate smoothly. |
3 | When in use, you must first connect to the spindle motor cooling water pipes, water pipes to ensure. Water flow is not less than 5L/min |
4 | If the electric spindle needs to be replaced with a new bearing, |
3, The common faults and their elimination methods
The Fault | The Reason | The Solution |
The electric spindle does not run after start | 1.No output or wrong setting for the inverter | check the output and setting of the inverter |
2.Plug not connected | check the plug and connection cable | |
3.the cable not connected | ||
4.The stator winding burned | change the stator | |
Few seconds after start,the spindle stop running | 1.water inlet | Drying stator |
2.High temperature induced wire insulation damage | change the stator | |
3.Lack of phase operation caused over current protection | check the cable connecting of the spindle motor | |
4.Start-up time is too short | Extended acceleration time | |
Motor smoke or shell hair hot | 1.The inverter output voltage, frequency is not match with the spindle motor | check the setting of the inverter |
2.the frequency of the inverter is not set correctly | reset the frequency of the inverter | |
3.Air duct blockage | check the air duct | |
Nut loosening when start | Rotation direction error | recorrect the rotation according the instruction on spindle |
Noise and vibration | 1,bearing damaged | change bearings |
2.Parts precision damage affect dynamic balance | Check dynamic balance | |
3.Large spindle runout | change spindle | |
Nut loosening when stop | Down time is too short | Prolonged deceleration time |
Return Policy
If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.
Seller Service
On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).Great Offers 300w 0.3kw ER8 60000rpm Precision High Speed spindle motor water cooling 75VAC 4.5A 1000HZ GDZ48-300 CNC Router
Comments
Post a Comment