Wonderful Sale 1.5HP 1.2kw ER11 60000rpm Precision High Speed spindle motor water cooling 220VAC 4.5A 1000HZ 62mm 4 bearings CNC Router

Best Water High Rating provide router net, router 1000mw, router repeaters Big Stock Sale 1.5HP 1.2kw ER11 60000rpm Precision High Speed spindle motor water cooling 220VAC 4.5A 1000HZ 62mm 4 bearings CNC Router. Get 43% discount Now! Now US $401.00/piece. Dont waste your time. Buy Now only in TOPCNC Store Trusted Seller Store!

1.5HP 1.2kw ER11 60000rpm Precision High Speed spindle motor water cooling 220VAC 4.5A 1000HZ 62mm 4 bearings CNC Router

1, Spindle Specification

Brand	CHANGSHENGI
Spindle Model	GDZ-62-1.2 60000
Dimension	62mm*202mm
Speed	60000rpm
Rated Power	1.2kW
Voltage	AC220V
Current	4.5A
Frequency	1000HZ
Bearings	2*7002C P4 DT & 2*7000C P4 DT
Collet	ER11(Random send a collet as free)
Cooling Type	Water cooling
Lubricate	Grease
Plug connection:	Plug in 1234 pin, 1-U, 2-V, 3-W, 4-GND or not connected. if 123 not connected correctly, the motor will reverse. Swap any two wires can be OK.

2, Instructions

1	The electric spindle must be matched with the frequency converter. Frequency converter selection must be matched with the power, voltage, current, frequency and other parameters of the electric spindle. The use of electric spindle must first set the benchmark frequency of the inverter. The reference frequency of the frequency converter is set according to the highest frequency of the electric spindle. Inverter reference frequency conversion factory default settings 50hz. If the base frequency of the inverter is not set before the spindle motor is used, the spindle motor can be burnt down.
2	Before use, you should use the hand to turn the spindle motor, and confirm that it can rotate smoothly.
3	When in use, you must first connect to the spindle motor cooling water pipes, water pipes to ensure. Water flow is not less than 5L/min
4	If the electric spindle needs to be replaced with a new bearing, Should be replaced by a certain professional and technical personnel. Supporting special tools. The spindle motor should be fully cleaned, the stator coil does not need to be removed.

3, The common faults and their elimination methods

The Fault	The Reason	The Solution
The electric spindle does not run after start	1.No output or wrong setting for the inverter	check the output and setting of the inverter
	2.Plug not connected	check the plug and connection cable
	3.the cable not connected
	4.The stator winding burned	change the stator
Few seconds after start,the spindle stop running	1.water inlet	Drying stator
	2.High temperature induced wire insulation damage	change the stator
	3.Lack of phase operation caused over current protection	check the cable connecting of the spindle motor
	4.Start-up time is too short	Extended acceleration time
Motor smoke or shell hair hot	1.The inverter output voltage, frequency is not match with the spindle motor	check the setting of the inverter
	2.the frequency of the inverter is not set correctly	reset the frequency of the inverter
	3.Air duct blockage	check the air duct
Nut loosening when start	Rotation direction error	recorrect the rotation according the instruction on spindle
Noise and vibration	1,bearing damaged	change bearings
	2.Parts precision damage affect dynamic balance	Check dynamic balance
	3.Large spindle runout	change spindle
Nut loosening when stop	Down time is too short	Prolonged deceleration time

Return Policy

If the product you receive is not as described or low quality, the seller promises that you may return it before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe) and receive a full refund. The return shipping fee will be paid by you. Or, you can choose to keep the product and agree the refund amount directly with the seller.
N.B.: If the seller provides the "Longer Protection" service on this product, you may ask for refund up to 15 days after order completion.

Seller Service

On-time Delivery: If you do not receive your purchase within 60 days, you can ask for a full refund before order completion (when you click "Confirm Order Received" or exceed confirmation timeframe).
Excellent Deals 1.5HP 1.2kw ER11 60000rpm Precision High Speed spindle motor water cooling 220VAC 4.5A 1000HZ 62mm 4 bearings CNC Router

Supported by Widhiarta | Powered by Aditif